This event is now over

Event Details

About

Arduino  

Hack, Tweak, Show, speed geeking, Talk, Debate, Panel Discussion,  ice breaking, 

++++++++++++++++++++++++++++
Drone + VR + 3D + 3D Print + Lucky Draw 
++++++++++++++++++++++++++++

 
09:00 Check In/Registration

 09:30 Opening/Arduino Introduction

 10:00 Local Makers Networking and Hangout

 10:30 Exhibition of Arduino based projects by attending makers

 11:30 Lunch Break

 12:30 Make'n Rush

 01:30 Showcase of Make'n Rush Projects

02:00 Best Make'n Rush Projects Announcement

02:05 Snack Break

02:15 Open Talk: Share knowledge, opinions and thoughts

02:45 Makerspace Introduction and call out for collaborations

03:15 Arduino Town Hall meeting and Future Plaining

04:45 Celebration and event closing

-----------------------------------------------------------

 

Training Day

2017 March
22, 23, 24 (9:30am to 3:30 pm)

Day 1
...........

09:30 - 10:00 | Introduction to Course, Course Structure
10:00 - 11:00 | Introduction to Electronics
11:15 - 12:15 | Introduction to Programming
12:15 - 01:15 | Lunch Break
01:15 - 02:00 | Intoduction to Arduino Platform
02:00 - 02:30 | Arduino Environment Setup
02:30 - 03:00 | Arduino Hardware
03:00 - 03:20 | Time to test Arduino Board and Arduino IDE
03:20 - 03:30 | End of Day 1, Brief Conclusion

Day 2
...........

09:30 - 10:00 | Introduction to Day 2, Sparkfun Inventor Kit Introduction
10:00 - 10:15 | A little warm up and preparation
10:15 - 10:45 | Circuit #1 Blinking a LED
10:45 - 11:00 | Circuit #2 Potentiometer
11:00 - 11:20 | Circuit #3 RGB LED
11:20 - 11:40 | Circuit #4 Multiple LEDs
11:40 - 12:00 | Circuit #5 Push Buttons
12:00 - 01:00 | Lunch Break
01:00 - 01:15 | Circuit #6 Photo Resistor
01:15 - 01:25 | Circuit #7 Temperature Sensor
01:25 - 01:45 | Circuit #8 A Single Servo
01:45 - 01:55 | Circuit #9 Flex Sensor (Potentiometer Controlled Servo)
01:55 - 02:00 | Break
02:00 - 02:20 | Circuit #10 Soft Potentiometer (Potentiometer Controlled RGB LED)
02:20 - 02:40 | Circuit #11 Buzzer
02:40 - 03:00 | Circuit #12 Spinning a Motor
03:00 - 03:15 | Circuit #13 Relays
03:15 - 03:45 | Circuit #15 LCD
03:45 - 03:50 | End of Day 2, Brief Conclusion

Day 3
...........

09:30 - 09:45 | Welcome Back
09:45 - 10:45 | PCB Skills (Boards, Soldering, Desoldering, etc.,)
10:45 - 11:00 | Group Gathering and Idea Discussion for Mini Project
11:00 - 12:00 | Mini Group Project
12:00 - 01:00 | Lunch Break
01:00 - 02:30 | Mini Group Project Continued
02:30 - 02:45 | Break
02:45 - 03:20 | Mini Group Project Continued
03:20 - 03:40 | End of Day 3 and Bootcamp, Conclusion

Contact

09450022022
Ko Ko Ye`
kokoye2007@gmail.com

Venue

Kanaung Hub.
Bld 14, 4th Fl, MICT Park, Hlaing Township
MICT Park, Hlaing Township
Yangon, Yangon
Myanmar

Map